Commercial mould cleaning and mould remediation

Commercial Mould Cleaning Methods Compared: What Works Where

Reviewed and updated February 2026 by Nick Roth, Mould Remediation Specialist, AllAces Cleaning & Restoration

The right choice between commercial mould cleaning methods depends on what the mould is growing on. Hard surfaces are cleaned in place with HEPA vacuuming and an antimicrobial wipe. Timber framing and plant can be dry ice blasted. Porous materials like plasterboard, ceiling tiles and carpet are usually removed.

In a workplace the method also has to fit around trading hours, occupants and insurers, which is why commercial jobs start with containment and a plan rather than a spray bottle.

This guide compares the main methods, where each one fits, and what a properly run commercial job looks like from inspection to clearance.

Key takeaways

Commercial mould cleaning methods compared

Short answer: most commercial jobs combine two or three of these, chosen room by room.

MethodBest forLimits
HEPA vacuuming and damp wipingHard, non-porous surfaces: metal, glass, sealed benchtopsSurface growth only
Antimicrobial cleaningHard and semi-porous surfaces after HEPA vacuumingNeeds dwell time and good ventilation
Dry ice blastingTimber framing, roof spaces, plant and machinerySpecialist equipment; noisy; cost
Removal and replacementPlasterboard, ceiling tiles, carpet, insulationNeeds containment and trades to rebuild
Pressure or soft washingExterior hard surfaces onlyNever indoors
HEPA air scrubbing and hydroxylAirborne spores and musty odourSupports cleaning; doesn't replace it
Commercial mould cleaning and mould remediation
Commercial mould jobs are planned around the building staying open: containment, staged areas and clearance before handover.

How each method works

HEPA vacuuming and damp wiping

A HEPA vacuum lifts loose spores without blowing them around, then surfaces are wiped with a detergent or antimicrobial solution. It’s the default for hard surfaces and the first step on almost every job.

Antimicrobial cleaning

A registered antimicrobial is applied and left for its dwell time, then wiped or rinsed. It’s useful on semi-porous surfaces like sealed timber and concrete once the loose growth is gone.

Dry ice blasting

Pellets of frozen carbon dioxide are blasted at the surface. They lift mould and staining off timber and equipment, then turn to gas, so no water is added and there’s little secondary waste. It suits roof spaces, subfloors and production plant.

Removal and replacement

Plasterboard, ceiling tiles, carpet and insulation hold mould inside the material. Under containment they’re cut out, bagged and replaced once the structure is dry. The IICRC S520 standard sets out when material should be removed rather than cleaned.

Exterior washing

Car parks, walls and walkways can be pressure or soft washed. Our guide to pressure washing for mould remediation covers which surfaces it suits and which it damages.

How a commercial job runs

  1. Inspect and map. Moisture readings, affected areas, and the water source. Our mould inspection and testing report becomes the scope.
  2. Plan around the business. Stage work by zone and hours so the site keeps trading where it can.
  3. Contain. Barriers, negative air and HEPA filtration around each work zone.
  4. Clean or remove. The methods above, matched to each material.
  5. Dry and fix the cause. Leaks, HVAC condensate, drainage or ventilation.
  6. Verify and hand back. Visual checks, moisture readings and clearance testing where required.

What causes mould in commercial buildings

Short answer: water the building can’t get rid of.

Our guide to what causes mould in the workplace goes through the common sources and how to catch them early.

Benefits of doing it properly

Less downtime

Staged work keeps most of the site open.

Healthier workplace

Fewer complaints about smells, allergies and air quality.

Documented result

Reports and clearance support insurance claims and lease obligations.

It stays fixed

Finding the water source stops repeat call-outs.

Safety

Short answer: commercial remediation involves spores, chemicals, dust and sometimes heights, so it needs trained people, PPE and containment.

Mould exposure affects people with asthma, allergies and weak immune systems most. The NSW Health mould fact sheet and Better Health Channel explain who is most at risk.

FAQs

There isn’t one. Hard surfaces are HEPA vacuumed and wiped, timber and equipment can be dry ice blasted, and porous materials like plasterboard and carpet are usually removed. Most jobs combine methods.

Yes, on timber framing, roof spaces and equipment. It removes growth without adding water, but it’s not a fix for plasterboard or carpet, which usually need replacing.

Often, yes. Work can be staged by zone with containment and negative air, so unaffected areas keep operating.

Through post-remediation checks: a visual inspection, moisture readings and, where required, air or surface sampling compared against the baseline.

The bottom line

Match the method to the material, contain the area, fix the water and verify the result. That’s what separates commercial remediation from a surface clean.

For a site-specific plan, our mould removal and remediation team can scope the job around your trading hours.

About the author

Nick Roth, Mould Remediation Specialist, AllAces Cleaning & Restoration

Nick has been with AllAces for more than six years and is our most experienced mould remediation specialist. He completed Decon Systems’ Mould Remediation for Technicians course in August 2021. Technicians in every state we work in call on him for the hardest mould testing and remediation jobs, including work with specialised equipment such as Hydroxyl machines.

Table of Contents